Characterisation of the Performance of a Structured Light Digitising Sensor by Using Different Materials and Surface Finishes
-
Zapico García, Pablo
1
- Cuesta, Eduardo 1
- Meana, Víctor 1
- Suárez, Germán 1
- Mateos, Sabino 1
-
Rodríguez González, Pablo
2
-
1
Universidad de Oviedo
info
-
2
Universidad de León
info
ISSN: 1662-9795
Argitalpen urtea: 2023
Alea: 961
Orrialdeak: 151-159
Mota: Artikulua
Beste argitalpen batzuk: Key Engineering Materials
Laburpena
The advantages of non-contact digitising systems over contact systems are undeniable. They allow capturing more information per unit of time with less accessibility problems and without alter the digitised surface. Although many of these systems have been developed with the aim of replacing contact systems in metrological verification tasks, generalist techniques such as photogrammetry, structured light, etc., have been developed over the years for digitising archaeological remains, works of art or living biological systems, among others. As is the case for non-contact measurement-oriented systems, for these generalist systems there are still difficulties in positioning them along a metrological traceability chain if they are required for any kind of measurement. This is due to the lack of specific standards, as well as the strong influence of the optical properties of the digitised surface on the quality of the results obtained. It is therefore necessary to develop calibration procedures and characterisation work to analyse this influence. The aim of this work is to characterise the metrological performance of one of these generalists structured light devices, Einscan-SP by Shining 3D, in the digitising of different calibration spheres made of different materials (WC, Al2O3, ZrO2, etc.) with different surface finishes (shot-blasted, polished, coated). As quality indicators, the number of points captured, the quality of the point cloud as well as the dimensional and geometrical deviation from the results obtained with a high-performance contact measurement system shall be used. Apart from the raw data, the influence of applying filtering to the captured clouds is analysed. The results of this work allow recommendations to be made regarding the material and finish of the spheres to be used, as well as the filtering to be applied, if necessary, in order to assess the metrological performance of this type of equipment.
Erreferentzia bibliografikoak
- D. Sims-Waterhouse, P. Bointon, S. Piano, R. K. Leach, Experimental comparison of photogrammetry for additive manufactured parts with and without laser speckle projection, Optical Measurement Systems for Industrial Inspection X. 10329 (2017) 220-226.
- J. M. Park, Comparative analysis on reproducibility among 5 intraoral scanners: sectional analysis according to restoration type and preparation outline form, The Journal of Advanced Prosthodontics. 8(5) (2016) 354-362.
- R. Richert, A. Goujat, L. Venet, G. Viguie, S. Viennot, P. Robinson, J. Farges, M. Fages, M. Ducret, Intraoral Scanner Technologies: A Review to Make a Successful Impression, Journal of healthcare engineering. 2017 (2017).
- P. Medina-Sotomayor, A. Pascual Moscardó, I. Camps Alemany, Relationship between resolution and accuracy of four intraoral scanners in complete-arch impressions, Journal section: Prosthetic Dentistry. 10(4) (2018), e361-e366.
- Shining 3D, Einscan-SE/SP Desktop 3D Scanner, https://encdn.shining3d.com/2020/08 /SE-SPen.pdf accessed on 25 January 2023.
- Sandoz, ZTA zirconia toughened alumina, https://sandoz.ch/wp-content/uploads/2021/09/ZTA_ zirconia_toughned.pdf, accessed on 25 January 2023.
- Shining 3D, Einscan SE/SP User Manual, v3.0.0.1, https://stomshop.pro/docs/shining-3d-einscan-se-sp-user-manual-eng.pdf, accessed on 25 January 2023.